New WIFI Speeds Up To 300 Times Faster

Researchers at the Eindhoven University of Technology (Netherlands) say their new wireless network that uses harmless infrared rays will make wifi speeds up to 300 times faster.


“What we are doing actually is using rays of light which convey the information in a wireless way, and each ray is acting as a very high capacity channel. It’s actually the same as an optical fibre without needing the fibre, and what we achieved up to this moment is 112 gigabits per second,” says Professor Ton Koonen, Eindhoven University of Technology.

That’s the equivalent data of three full-length movies being downloaded per second. Light antennas radiate multiple invisible wavelengths at various angles. If a user’s smartphone or tablet moves out of one antenna’s sightline, another takes over. Infrared wavelengths don’t go into your eyes, making them safe to use. The lack of moving parts makes the system maintenance and power-free. While each user gets their own antenna.

The big benefits we see of our technique is that you offer unshared capacity to each individual user, so you get a guaranteed capacity. Next to that you only get a beam if you need the traffic. So we’re not illuminating the whole place where maybe a single user is there. That means it’s much more power efficient. Another efficiency, another advantage, is that light doesn’t go through walls. So that means your communication is really confined to the particular room. Nobody can listen in from outside, so it offers you a lot of security,” explains rofessor Ton Koonen.
The team is seeking funding to help make the technology widespread within five years.


No More Batteries For Cellphones

University of Washington (UW) researchers have invented a cellphone that requires no batteries — a major leap forward in moving beyond chargers, cords and dying phones. Instead, the phone harvests the few microwatts of power it requires from either ambient radio signals or light.

The team also made Skype calls using its battery-free phone, demonstrating that the prototype made of commercial, off-the-shelf components can receive and transmit speech and communicate with a base station.


We’ve built what we believe is the first functioning cellphone that consumes almost zero power,” said co-author Shyam Gollakota, an associate professor in the Paul G. Allen School of Computer Science & Engineering at the UW. “To achieve the really, really low power consumption that you need to run a phone by harvesting energy from the environment, we had to fundamentally rethink how these devices are designed.”

The team of UW computer scientists and electrical engineers eliminated a power-hungry step in most modern cellular transmissionsconverting analog signals that convey sound into digital data that a phone can understand. This process consumes so much energy that it’s been impossible to design a phone that can rely on ambient power sources. Instead, the battery-free cellphone takes advantage of tiny vibrations in a phone’s microphone or speaker that occur when a person is talking into a phone or listening to a call.

An antenna connected to those components converts that motion into changes in standard analog radio signal emitted by a cellular base station. This process essentially encodes speech patterns in reflected radio signals in a way that uses almost no power. To transmit speech, the phone uses vibrations from the device’s microphone to encode speech patterns in the reflected signals. To receive speech, it converts encoded radio signals into sound vibrations that that are picked up by the phone’s speaker. In the prototype device, the user presses a button to switch between these two “transmitting” and “listening” modes.

The new technology is detailed in a paper published July 1 in the Proceedings of the Association for Computing Machinery on Interactive, Mobile, Wearable and Ubiquitous Technologies.


SuperPowerful Tiny Device Converts Light Into Electricity

In today’s increasingly powerful electronics, tiny materials are a must as manufacturers seek to increase performance without adding bulk. Smaller also is better for optoelectronic devices — like camera sensors or solar cells —which collect light and convert it to electrical energy. Think, for example, about reducing the size and weight of a series of solar panels, producing a higher-quality photo in low lighting conditions, or even transmitting data more quickly.

However, two major challenges have stood in the way: First, shrinking the size of conventionally used “amorphousthin-film materials also reduces their quality. And second, when ultrathin materials become too thin, they are almost transparent — and actually lose some ability to gather or absorb light.

Now, in a nanoscale photodetector that combines both a unique fabrication method and light-trapping structures, a team of engineers from the University at Buffalo (UB) and the University of Wisconsin-Madison (UW-Madison) has overcome both of those obstacles. The researchers — electrical engineers Qiaoqiang Gan at UB, and Zhenqiang (Jack) Ma and Zongfu Yu at UW-Madison — described their device, a single-crystalline germanium nanomembrane photodetector on a nanocavity substrate, in the July 7, 2017, issue of the journal Science Advances.

This image shows the different layers of the nanoscale photodetector, including germanium (red) in between layers of gold or aluminum (yellow) and aluminum oxide (purple). The bottom layer is a silver substrate

We’ve created an exceptionally small and extraordinarily powerful device that converts light into energy,” says Gan, associate professor of electrical engineering in UB’s School of Engineering and Applied Sciences, and one of the paper’s lead authors. “The potential applications are exciting because it could be used to produce everything from more efficient solar panels to more powerful optical fibers.”

The idea, basically, is you want to use a very thin material to realize the same function of devices in which you need to use a very thick material,” says Ma, the Lynn H. Matthias Professor and Vilas Distinguished Achievement Professor in electrical and computer engineering at UW-Madison, also a lead author. Nanocavities are made up of an orderly series of tiny, interconnected molecules that essentially reflect, or circulate, light.

The new device is an advancement of Gan’s work developing nanocavities that increase the amount of light that thin semiconducting materials like germanium can absorb. It consists of nanocavities sandwiched between a top layer of ultrathin single-crystal germanium and a bottom, reflecting layer of silver.


Device Doubles The Energy Conversion Of Solar Cells

Scientists from Japan are utilizing nanotechnology advancements to strengthen solar cellsSolar cells convert light into electricity using a bevy of sources, including light from the sun and the burning of natural resources such as oil and natural gas. However, the cells do not convert all light to power equally, which led to scientists attempting to find ways to produce more power. The flame of a gas burner will shift from red to blue as the heat increases because higher temperatures emit light at shorter wavelengths. Higher heat offers more energy, making short wavelengths an important target in the design of solar cells. Kyoto University‘s Takashi Asano, began using optical technologies to improve energy production.

device to double the power of solar cells

Current solar cells are not good at converting visible light to electrical power. The best efficiency is only around 20 percent,” Asano said in a statement. “The problem is that heat dissipates light of all wavelengths, but a solar cell will only work in a narrow range. To solve this, we built a new nano-sized semiconductor that narrows the wavelength bandwidth to concentrate the energy.

The researchers were able to use their nanoscale semiconductor to raise the energy conversion rate to at least 40 percent. Asano and researchers at the Susumu Noda lab had previously attempted to work with higher wavelengths. “Our first device worked at high wavelengths but to narrow output for visible light required a new strategy, which is why we shifted to intrinsic silicon in this current collaboration with Osaka Gas,” Asano said. Visible wavelengths are emitted at 1000 degrees Celsius but conveniently silicon has a melting temperature of over 1,400 degrees Celsius.

This concept was utilized by the scientists, who etched silicon plates to have a large number of identical and equidistantly-spaced rods, the height, radii and spacing of which was optimized for the target bandwidth. Susumu Noda, a professor at Kyoto University, explained the benefits of the advancement: “Our technology has two important benefits. First is energy efficiency: we can convert heat into electricity much more efficiently than before. Secondly is design:  we can now create much smaller and more robust transducers, which will be beneficial in a wide range of applications.”

The study was published in Science Advances.


Light-Controlled NanoRobot Attacks Tumors

A team of researchers led by Dr Jinyao Tang of the Department of Chemistry, the University of Hong Kong, has developed the world’s first light-seeking synthetic Nano robot. With size comparable to a blood cell, those tiny robots have the potential to be injected into patients’ bodies, helping surgeons to remove tumors and enabling more precise engineering of targeted medications.

It has been a dream in science fiction for decades that tiny robots can fundamentally change our daily life. The famous science fiction movie “Fantastic Voyage” is a very good example, with a group of scientists driving their miniaturized Nano-submarine inside human body to repair a damaged brain. In the film “Terminator 2”, billions of Nanorobots were assembled into the amazing shapeshifting body: the T-1000.


“Light is a more effective option to communicate between microscopic world and macroscopic world. We can conceive that more complicated instructions can be sent to Nanorobots which provide scientists with a new tool to further develop more functions into Nanorobot and get us one step closer to daily life applications”

The Nobel Prize in Chemistry 2016 was awarded to three scientists for “the design and synthesis of molecular machines”. They developed a set of mechanical components at molecular scale which may be assembled into more complicated Nano machines to manipulate single molecule such as DNA or proteins in the future. The development of tiny nanoscale machines for biomedical applications has been a major trend of scientific research in recent years. Any breakthroughs will potentially open the door to new knowledge and treatments of diseases and development of new drugs.

One difficulty in Nanorobot design is to make these nanostructures sense and respond to the environment. Given each Nanorobot is only a few micrometer in size which is ~50 times smaller than the diameter of a human hair, it is very difficult to squeeze normal electronic sensors and circuits into Nanorobots with reasonable price. Currently, the only method to remotely control Nanorobots is to incorporate tiny magnetic inside the Nanorobot and guide the motion via external magnetic field.

The Nanorobot developed by Dr Tang’s team use light as the propelling force, and is the first research team globally to explore the light-guided Nanorobot and demonstrate its feasibility and effectiveness. In their paper published in Nature Nanotechnology, Dr Tang’s team demonstrated the unprecedented ability of these light-controlled Nanorobots as they are “dancing” or even spell a word under light control. With a novel Nanotree structure, the Nanorobots can respond to the light shining on it like moths being drawn to flames. Dr Tang described the motions as if “they can “see” the light and drive itself towards it”.

The findings have been published in the scientific journal Nature Nanotechnology.


Solar Powered House: Tiles Instead Of Panels

Tesla founder and CEO Elon Musk wasn’t kidding when he said that the new Tesla solar roof product was better looking than an ordinary roof: the roofing replacement with solar energy gathering powers does indeed look great. It’s a far cry from the obvious and somewhat weird aftermarket panels you see applied to roofs after the fact today.


The solar roofing comes in four distinct styles that Tesla presented at the event, including “Textured Glass Tile,” “Slate Glass Tile,” “Tuscan Glass Tile, and “Smooth Glass Tile.” Each of these achieves a different aesthetic look, but all resembled fairly closely a current roofing material style. Each is also transparent to solar, but appears opaque when viewed from an angle.

The current versions of the tiles actually have a two percent loss on efficiency, so 98 percent of what you’d normally get from a traditional solar panel, according to Elon Musk. But the company is working with 3M on improved coatings that have the potential to possibly go above normal efficiency, since it could trap the light within, leading to it bouncing around and resulting in less energy loss overall before it’s fully diffused.

Of course, there’s the matter of price: Tesla’s roof cost less than the full cost of a roof and electricity will be competitive or better than the cost of a traditional roof combined with the cost of electricity from the grid, Musk said. Tesla declined to provide specific pricing at the moment, since it will depend on a number of factor including installation specifics on a per home basis.

Standard roofing materials do not provide fiscal benefit back to the homeowner post-installation, besides improving the cost of the home. Tesla’s product does that, by generating enough energy to fully power a household, with the power designed to be stored in the new Powerwall 2.0 battery units so that homeowners can keep a reserve in case of excess need.

The solar roof product should start to see installations by summer next year, and Tesla plans to start with one or two of its four tile options, then gradually expand the options over time. As they’re made from quartz glass, they should last way longer than an asphalt tile — at least two or three times the longevity, though Musk later said “they should last longer than the house”.


NanoRobots With Grippers Travel Through the Bloodstream To Capture Cancer Cells

A research team at Worcester Polytechnic Institute (WPI) has developed a revolutionary, light-activated semiconductor nanocomposite material that can be used in a variety of applications, including microscopic actuators and grippers for surgical robots, light-powered micro-mirrors for optical telecommunications systems, and more efficient solar cells and photodetectors.

nanorobotsThis is a new area of science,” said Balaji Panchapakesan, associate professor of mechanical engineering at WPI and lead author of a paper about the new material published in Scientific Reports, an open access journal from the publishers of Nature. “Very few materials are able to convert photons directly into mechanical motion. In this paper, we present the first semiconductor nanocomposite material known to do so. It is a fascinating material that is also distinguished by its high strength and its enhanced optical absorption when placed under mechanical stress.”

Tiny grippers and actuators made with this material could be used on Mars rovers to capture fine dust particles.” Panchapakesan noted. “They could travel through the bloodstream on tiny robots to capture cancer cells or take minute tissue samples. The material could be used to make micro-actuators for rotating mirrors in optical telecommunications systems; they would operate strictly with light, and would require no other power source.”

Like other semiconductor materials, molybdenum disulfide, the material described in the Scientific Report paper, is characterized by the way electrons are arranged and move about within its atoms.


Light Makes OscillatorTo Oscillate Indefinitely

Researchers have designed a device that uses light to manipulate its mechanical properties. The device, which was fabricated using a plasmomechanical metamaterial, operates through a unique mechanism that couples its optical and mechanical resonances, enabling it to oscillate indefinitely using energy absorbed from light.

metamaterialThis work demonstrates a metamaterial-based approach to develop an optically-driven mechanical oscillator. The device can potentially be used as a new frequency reference to accurately keep time in GPS, computers, wristwatches and other devices, researchers said. Other potential applications that could be derived from this metamaterial-based platform include high precision sensors and quantum transducers..

Researchers engineered the metamaterial-based device by integrating tiny light absorbing nanoantennas onto nanomechanical oscillators. The study was led by Ertugrul Cubukcu, a professor of nanoengineering and electrical engineering at the University of California San Diego. The work, which Cubukcu started as a faculty member at the University of Pennsylvania and is continuing at the Jacobs School of Engineering at UC San Diego, demonstrates how efficient light-matter interactions can be utilized for applications in novel nanoscale devices.

Metamaterials are artificial materials that are engineered to exhibit exotic properties not found in nature. For example, metamaterials can be designed to manipulate light, sound and heat waves in ways that can’t typically be done with conventional materials.

Metamaterials are generally considered “lossy” because their metal components absorb light very efficiently. “The lossy trait of metamaterials is considered a nuisance in photonics applications and telecommunications systems, where you have to transmit a lot of power. We’re presenting a unique metamaterials approach by taking advantage of this lossy feature,” Cubukcu said. The researchers also point out that because the plasmomechanical metamaterial can efficiently absorb light, it can function under a broad optical resonance. That means this metamaterial can potentially respond to a light source like an LED and won’t need a strong laser to provide the energy.

Using plasmonic metamaterials, we were able to design and fabricate a device that can utilize light to amplify or dampen microscopic mechanical motion more powerfully than other devices that demonstrate these effects. Even a non-laser light source could still work on this device,” said Hai Zhu, a former graduate student in Cubukcu’s lab and first author of the study.

Optical metamaterials enable the chip-level integration of functionalities such as light-focusing, spectral selectivity and polarization control that are usually performed by conventional optical components such as lenses, optical filters and polarizers. Our particular metamaterial-based approach can extend these effects across the electromagnetic spectrum,” adds Fei Yi, a postdoctoral researcher who worked in Cubukcu’s lab.

The research was published in the journal Nature Photonics.


Solar Cells : How To Boost Efficiency Up To 30%

Researchers from the University of Houston have reported the first explanation for how a class of materials changes during production to more efficiently absorb light, a critical step toward the large-scale manufacture of better and less-expensive solar panels. The work, published this month as the cover story for Nanoscale, offers a mechanism study of how a perovskite thin film changes its microscopic structure upon gentle heating, said Yan Yao, assistant professor of electrical and computer engineering and lead author on the paper. This information is crucial for designing a manufacturing process that can consistently produce high-efficiency solar panels.

Perovskite cheap

Last year Yao and other researchers identified the crystal structure of the non-stoichiometric intermediate phase as the key element for high-efficiency perovskite solar cells. But what happened during the later thermal annealing step remained unclear. The work is fundamental science, Yao said, but critical for processing more efficient solar cells.

Otherwise, it’s like a black box,” he said. “We know certain processing conditions are important, but we don’t know why.”

The work also yielded a surprise: the materials showed a peak efficiency – the rate at which the material converted light to electricity – before the intermediate phase transformation was complete, suggesting a new way to produce the films to ensure maximum efficiency. Yao said researchers would have expected the highest efficiency to come after the material had been converted to 100 percent perovskite film. Instead, they discovered the best-performing solar devices were those for which conversion was stopped at 18 percent of the intermediate phase, before full conversion.

We found that the phase composition and morphology of solvent engineered perovskite films are strongly dependent on the processing conditions and can significantly influence photovoltaic performance,” the researchers wrote. “The strong dependence on processing conditions is attributed to the molecular exchange kinetics between organic halide molecules and DMSO (dimethyl sulfoxide) coordinated in the intermediate phase.

Perovskite compounds commonly are comprised of a hybrid organic-inorganic lead or tin halide-based material and have been pursued as potential materials for solar cells for several years. Yao said their advantages include the fact that the materials can work as very thin films – about 300 nanometers, compared with between 200 and 300 micrometers for silicon wafers, the most commonly used material for solar cells. Perovskite solar cells also can be produced by solution processing at temperatures below 150 degrees Centigrade (about 300 degrees Fahrenheit) making them relatively inexpensive to produce.

At their best, perovskite solar cells have an efficiency rate of about 22 percent, slightly lower than that of silicon (25 percent). But the cost of silicon solar cells is also dropping dramatically, and perovskite cells are unstable in air, quickly losing efficiency. They also usually contain lead, a toxin.

Still, Yao said, the materials hold great promise for the solar industry, even if they are unlikely to replace silicon entirely. Instead, he said, they could be used in conjunction with silicon, boosting efficiency to 30 percent or so.


Vertical Farming

Odds are this isn’t like other farms you’re used to. Located in a warehouse in an urban New Jersey neighborhood,  Aerofarms grows crops year-round without using soil or sunlight. The company has an ambitious goal: to grow high-yielding crops using economical methods that will provide locally sourced food to the community.

“We need a new way to feed our planet. Aerofarms presents one of the solutions to do so. Here we can grow in cities, in warehouses in cities, so we’re close to where the mouths are, reducing those transport miles and basically do more with less. That’s what we need to do. We use to grow our plants, about 95 percent less water to grow the plants, about 50 percent less fertilizer as nutrients and … zero pesticides, herbicides, fungicides“, says David rosenberg, CEO of Aerofarms.

Inside, the 30,000 square foot building (2,800 square meter) are crops of kale, arugula and watercress illuminated by rows of light emitting diodes, or LED lamps, and planted in white fabric made from recycled water bottles. The levels of light, temperature and nutrients reaching each plant in the tall columns are controlled using what AeroFarms describes as a patented growing algorithm.

We can take that exact same seed for leafy greens that out in the field can take 30-45 days to grow and grow it in 12-16 days. It’s always about optimizing. We’re giving it the right nutrients. So we’re looking at the macro nutrients, the micro nutrients, we are adjusting based on the plant variety, the stage of maturation, and we’re able to again, deliver a higher quality product more consistently all year round“, says co-founder and Chief marketing officer Marc Oshima.

The result according to Oshima – a farm that can be 75 times more productive. The company’s model also eliminates transportation of crops from grow states like California and Arizona to consumers in the Northeast. While they aren’t saying just how much food they produce, plans are in development for a larger Newark facility, and 25 more farms in the United States and abroad over the next five years. If growth continues at that rate we could one day see our cities rival the countryside as the home of agriculture.


90 Minutes To Annihilate Early Stage Prostate Cancer

A prostate cancer patient undergoing a new photodynamic therapy that’s exciting specialists. Developed in Israel, treatment takes 90 minutes and involves no radiation or chemotherapy. It’s pain free and tests in Latin America showed an impressive clear-up rate and minimal side effects for early stage patients.

Prostate cancer

The patient may be cured, he may not be even cured of his disease but he may have a remedy for 20-30 years which is exactly what we need. Most of these patients are men the age of 60-70, not all of them healthy, and if you give them 10-20 years with good health and without side effects, which is the main thing, then we’ve done a great thing and we’ve done a revolution“, says Professor Jack Baniel, Chief Urologist at the Ramat Aviv Medical Center.

Israeli start-up Steba Research developed the therapy, in conjunction with Weizmann Insititute professors. It’s a focal therapy, which destroys tumours in the prostate while leaving the gland and most tissue intact. Using ultrasound, doctors insert conductors into the body, close to blood vessels feeding the tumour. Illuminating optic fibres are placed inside the conductors. A drug called Tookad that makes light toxic to living tissue is injected into the patient’s blood.

When doctors light up the optic fibres inside the patient, the cells touched by light die instantly. This patient is delighted with his treatment.  “So one day after the treatment I was back at home and three days later I was back at the office with regular life like before, and today after I got the new MRI I found out that my life is back again and everything is like before, no side affects, sexual life like before and I feel great“, comments Yaron Sfadia, patient.
The treatment has already been approved in Mexico. Phase III trials are currently taking place in New York and the developers are confident it won’t be long before the treatment becomes widespread. Future work to extend the same photodynamic principles to other types of cancers is possible.


Algae To Power Jets

Aviation giant Airbus hope algae could one day help power jets – and help airlines cut their C02 emissions. They’re working with the Munich Technical University (Germany) to cultivate the photosynthetic organisms in this lab. Algae here is cultivated in water with a salt content of 6-9 percent. A combination of light and carbon dioxide does the rest.


Primarily you need obviously algae cells that are able to generate fats and oils. In combination with CO2 and light these algae cells propagate and form algae biomass and under certain cultivation conditions, for example the lack of nitrogen in the cultivation media, these algae cells accumulate fats and oils in their cell mass and this can reach up to 50 to 70 percent of the total cell weight. That is quite a lot and once you formed that fat and oil you can actually extract it from the cell and convert it over a chemical process“, says  Thomas Brueck, Professor at Munich Technical University (TUM). In these open tanks algae grows 12 times faster than plants cultivated on soil, producing an oil yield 30 times that of rapeseed.

Algae fuel today is still in the state of research so today, we could probably not offer it at costs which are realistic to run an airline. But we are sure that over time, we will make it possible to offer kerosine made of algae for a competitive price“, comments Gregor von Kursell, Airbus Group Spokesman. The company says the project remains in its infancy. Researchers believe biofuel from algaculture could provide up to 5 percent of jetfuel needs by around 2050.